VGN-FZ21M Motion Eye [ΕΠΙΛΥΘΗΚΕ]

[grammo]

Ε ναι λοιπόν! Επιλύθηκε

[logari81]

πολυ ωραία, πατησε το κουμπακι με το πρασινο "ν" στο ποστ που εμπεριεχει την απαντηση που σε βοηθησε.

Αν μετα από αναβάθμιση του πυρήνα παψει να δουλευει ισως χρειαστει να επαναλαβεις καποια απο τα βηματα που εκανες. Συγκεκριμενα:

Κώδικας: Επιλογή όλων


cd r5u87x
sudo make clean
sudo make
cd ..
sudo cp -r r5u87x/loader /usr/bin/loader-r5u87x


[grammo]

Σε ευχαριστώ πολύ για το χρόνο σου!

[grammo]

Αυτό απλά δεν υπάρχει... Σήμερα δε λειτουργεί πάλι...

Με τις παρακάτω εντολές

Κώδικας: Επιλογή όλων

sudo /usr/bin/loader-r5u87x
sudo rmmod uvcvideo && sudo modprobe uvcvideo
sudo /etc/init.d/hal restart

Παίρνω αυτά τα αποτελέσματα:

Κώδικας: Επιλογή όλων

sudo /usr/bin/loader-r5u87x
[sudo] password for stephanos:
r5u87x firmware loader v0.2

Searching for device...
Found camera: 05ca:183b
Camera reports positive microcode state.
Camera reports microcode version 0x0131.
Not doing anything - camera already setup.

Successfully uploaded firmware to device 05ca:183b!
stephanos@stephanos-laptop:~$ sudo rmmod uvcvideo && sudo modprobe uvcvideo
stephanos@stephanos-laptop:~$ sudo /etc/init.d/hal restart
* Restarting Hardware abstraction layer hald [ OK ]


Ε, πώς γίνεται σήμερα να μη δουλεύει;

[logari81]

πόσταρε το αποτελεσαμα των εντολών

Κώδικας: Επιλογή όλων

dmesg
uname -a

[grammo]

Τα αποτελέσματα της dmesg:

Κώδικας: Επιλογή όλων

[ 0.570047] pci 0000:09:03.0: PREFETCH window: 0x88000000-0x8bffffff
[ 0.570052] pci 0000:09:03.0: MEM window: 0x90000000-0x93ffffff
[ 0.570058] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09
[ 0.570062] pci 0000:00:1e.0: IO window: 0x7000-0x7fff
[ 0.570068] pci 0000:00:1e.0: MEM window: 0xfc100000-0xfc1fffff
[ 0.570073] pci 0000:00:1e.0: PREFETCH window: 0x00000088000000-0x0000008bffffff
[ 0.570088] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.570092] pci 0000:00:01.0: setting latency timer to 64
[ 0.570101] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.570107] pci 0000:00:1c.0: setting latency timer to 64
[ 0.570116] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.570121] pci 0000:00:1c.1: setting latency timer to 64
[ 0.570131] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.570136] pci 0000:00:1c.2: setting latency timer to 64
[ 0.570145] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.570150] pci 0000:00:1c.4: setting latency timer to 64
[ 0.570159] pci 0000:00:1e.0: setting latency timer to 64
[ 0.570169] pci 0000:09:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.570176] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.570178] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.570180] bus: 01 index 0 io port: [0x2000-0x2fff]
[ 0.570182] bus: 01 index 1 mmio: [0xcc000000-0xceffffff]
[ 0.570184] bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
[ 0.570186] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.570188] bus: 02 index 0 io port: [0x3000-0x3fff]
[ 0.570190] bus: 02 index 1 mmio: [0xf6000000-0xf7ffffff]
[ 0.570192] bus: 02 index 2 mmio: [0xf0000000-0xf1ffffff]
[ 0.570194] bus: 02 index 3 mmio: [0x0-0x0]
[ 0.570196] bus: 04 index 0 io port: [0x4000-0x4fff]
[ 0.570198] bus: 04 index 1 mmio: [0xf8000000-0xf9ffffff]
[ 0.570200] bus: 04 index 2 mmio: [0xf2000000-0xf3ffffff]
[ 0.570201] bus: 04 index 3 mmio: [0x0-0x0]
[ 0.570203] bus: 06 index 0 io port: [0x5000-0x5fff]
[ 0.570205] bus: 06 index 1 mmio: [0xfa000000-0xfbffffff]
[ 0.570207] bus: 06 index 2 mmio: [0xf4000000-0xf5ffffff]
[ 0.570209] bus: 06 index 3 mmio: [0x0-0x0]
[ 0.570211] bus: 08 index 0 io port: [0x6000-0x6fff]
[ 0.570213] bus: 08 index 1 mmio: [0xfc000000-0xfc0fffff]
[ 0.570215] bus: 08 index 2 mmio: [0x0-0x0]
[ 0.570216] bus: 08 index 3 mmio: [0x0-0x0]
[ 0.570218] bus: 09 index 0 io port: [0x7000-0x7fff]
[ 0.570220] bus: 09 index 1 mmio: [0xfc100000-0xfc1fffff]
[ 0.570222] bus: 09 index 2 mmio: [0x88000000-0x8bffffff]
[ 0.570224] bus: 09 index 3 io port: [0x00-0xffff]
[ 0.570226] bus: 09 index 4 mmio: [0x000000-0xffffffff]
[ 0.570228] bus: 0a index 0 io port: [0x7000-0x70ff]
[ 0.570230] bus: 0a index 1 io port: [0x7400-0x74ff]
[ 0.570232] bus: 0a index 2 mmio: [0x88000000-0x8bffffff]
[ 0.570235] bus: 0a index 3 mmio: [0x90000000-0x93ffffff]
[ 0.570242] NET: Registered protocol family 2
[ 0.581049] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.581284] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.581604] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.581774] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.581777] TCP reno registered
[ 0.585068] NET: Registered protocol family 1
[ 0.585184] checking if image is initramfs... it is
[ 1.184287] Freeing initrd memory: 7359k freed
[ 1.184325] Simple Boot Flag at 0x36 set to 0x1
[ 1.184493] cpufreq: No nForce2 chipset.
[ 1.184618] audit: initializing netlink socket (disabled)
[ 1.184634] type=2000 audit(1243247709.184:1): initialized
[ 1.191632] highmem bounce pool size: 64 pages
[ 1.191637] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.192914] VFS: Disk quotas dquot_6.5.1
[ 1.192972] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.193555] fuse init (API version 7.10)
[ 1.193638] msgmni has been set to 1698
[ 1.193804] alg: No test for stdrng (krng)
[ 1.193815] io scheduler noop registered
[ 1.193818] io scheduler anticipatory registered
[ 1.193820] io scheduler deadline registered
[ 1.193833] io scheduler cfq registered (default)
[ 1.194027] pci 0000:01:00.0: Boot video device
[ 1.210136] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 1.210174] pcieport-driver 0000:00:01.0: found MSI capability
[ 1.210198] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[ 1.210208] pci_express 0000:00:01.0:pcie00: allocate port service
[ 1.210222] pci_express 0000:00:01.0:pcie02: allocate port service
[ 1.210234] pci_express 0000:00:01.0:pcie03: allocate port service
[ 1.210286] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.210337] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.210372] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[ 1.210388] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 1.210400] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 1.210412] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 1.210487] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 1.210539] pcieport-driver 0000:00:1c.1: found MSI capability
[ 1.210573] pcieport-driver 0000:00:1c.1: irq 2301 for MSI/MSI-X
[ 1.210590] pci_express 0000:00:1c.1:pcie00: allocate port service
[ 1.210602] pci_express 0000:00:1c.1:pcie02: allocate port service
[ 1.210613] pci_express 0000:00:1c.1:pcie03: allocate port service
[ 1.210692] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 1.210743] pcieport-driver 0000:00:1c.2: found MSI capability
[ 1.210778] pcieport-driver 0000:00:1c.2: irq 2300 for MSI/MSI-X
[ 1.210794] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 1.210806] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 1.210818] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 1.210894] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 1.210945] pcieport-driver 0000:00:1c.4: found MSI capability
[ 1.210980] pcieport-driver 0000:00:1c.4: irq 2299 for MSI/MSI-X
[ 1.210996] pci_express 0000:00:1c.4:pcie00: allocate port service
[ 1.211009] pci_express 0000:00:1c.4:pcie02: allocate port service
[ 1.211024] pci_express 0000:00:1c.4:pcie03: allocate port service
[ 1.211108] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.213104] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.214442] ACPI: AC Adapter [ADP1] (on-line)
[ 1.221274] ACPI: Battery Slot [BAT0] (battery absent)
[ 1.221341] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 1.222518] ACPI: Lid Switch [LID0]
[ 1.222581] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.222591] ACPI: Power Button (CM) [PWRB]
[ 1.226050] ACPI: SSDT 7FED8D75, 02A1 (r1 Sony VAIO 20070704 PTL 20050624)
[ 1.226450] ACPI: SSDT 7FED882C, 04B7 (r1 Sony VAIO 20070704 PTL 20050624)
[ 1.228929] Monitor-Mwait will be used to enter C-1 state
[ 1.228933] Monitor-Mwait will be used to enter C-2 state
[ 1.228936] Monitor-Mwait will be used to enter C-3 state
[ 1.228948] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.228972] processor ACPI_CPU:00: registered as cooling_device0
[ 1.228975] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.229413] ACPI: SSDT 7FED9016, 00E4 (r1 Sony VAIO 20070704 PTL 20050624)
[ 1.229779] ACPI: SSDT 7FED8CE3, 0092 (r1 Sony VAIO 20070704 PTL 20050624)
[ 1.231001] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 1.231019] processor ACPI_CPU:01: registered as cooling_device1
[ 1.231023] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.242530] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.246154] ACPI: Thermal Zone [TZ00] (47 C)
[ 1.247897] thermal LNXTHERM:02: registered as thermal_zone1
[ 1.250813] ACPI: Thermal Zone [TZ01] (47 C)
[ 1.250866] isapnp: Scanning for PnP cards...
[ 1.605673] isapnp: No Plug & Play device found
[ 1.612225] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.613208] brd: module loaded
[ 1.613505] loop: module loaded
[ 1.613568] Fixed MDIO Bus: probed
[ 1.613573] PPP generic driver version 2.4.2
[ 1.613624] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.613651] Driver 'sd' needs updating - please use bus_type methods
[ 1.613660] Driver 'sr' needs updating - please use bus_type methods
[ 1.613697] ahci 0000:00:1f.2: version 3.0
[ 1.613711] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.613749] ahci 0000:00:1f.2: irq 2298 for MSI/MSI-X
[ 1.613807] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode
[ 1.613810] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
[ 1.613816] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.613921] scsi0 : ahci
[ 1.614001] scsi1 : ahci
[ 1.614057] scsi2 : ahci
[ 1.614116] ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 2298
[ 1.614118] ata2: DUMMY
[ 1.614120] ata3: DUMMY
[ 1.932021] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.932860] ata1.00: ACPI cmd ef/90:03:00:00:00:a0 succeeded
[ 1.932863] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 1.933200] ata1.00: ATA-8: FUJITSU MHY2200BH, 0000000B, max UDMA/100
[ 1.933203] ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.934089] ata1.00: ACPI cmd ef/90:03:00:00:00:a0 succeeded
[ 1.934091] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 1.934445] ata1.00: configured for UDMA/100
[ 1.948117] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHY2200B 0000 PQ: 0 ANSI: 5
[ 1.948205] sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors: (200 GB/186 GiB)
[ 1.948220] sd 0:0:0:0: [sda] Write Protect is off
[ 1.948222] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.948247] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.948305] sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors: (200 GB/186 GiB)
[ 1.948319] sd 0:0:0:0: [sda] Write Protect is off
[ 1.948321] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.948345] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.948348] sda: sda1 sda2 sda3 sda4
[ 2.017703] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.017742] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.017793] ata_piix 0000:00:1f.1: version 2.12
[ 2.017800] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.017834] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 2.017900] scsi3 : ata_piix
[ 2.017951] scsi4 : ata_piix
[ 2.018725] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
[ 2.018727] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
[ 2.180480] ata4.00: ATAPI: MATSHITABD-CMB UJ-120, 1.03, max UDMA/33
[ 2.196438] ata4.00: configured for UDMA/33
[ 2.365273] scsi 3:0:0:0: CD-ROM MATSHITA BD-CMB UJ-120 1.03 PQ: 0 ANSI: 5
[ 2.371272] sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.371275] Uniform CD-ROM driver Revision: 3.20
[ 2.371360] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 2.371394] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 2.372045] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.372062] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.372076] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.372080] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.372132] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 2.376046] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.376053] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.376070] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc404800
[ 2.388009] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 2.388072] usb usb1: configuration #1 chosen from 1 choice
[ 2.388097] hub 1-0:1.0: USB hub found
[ 2.388104] hub 1-0:1.0: 4 ports detected
[ 2.388205] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.388218] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.388222] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.388261] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.392160] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.392167] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.392179] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc404c00
[ 2.404009] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.404068] usb usb2: configuration #1 chosen from 1 choice
[ 2.404092] hub 2-0:1.0: USB hub found
[ 2.404099] hub 2-0:1.0: 6 ports detected
[ 2.404191] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.404207] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.404228] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.404234] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.404237] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.404282] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.404318] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 2.404388] usb usb3: configuration #1 chosen from 1 choice
[ 2.404412] hub 3-0:1.0: USB hub found
[ 2.404418] hub 3-0:1.0: 2 ports detected
[ 2.404504] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.404511] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.404514] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.404552] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 2.404587] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 2.404656] usb usb4: configuration #1 chosen from 1 choice
[ 2.404680] hub 4-0:1.0: USB hub found
[ 2.404686] hub 4-0:1.0: 2 ports detected
[ 2.404768] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.404775] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.404778] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.404824] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.404852] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 2.404924] usb usb5: configuration #1 chosen from 1 choice
[ 2.404952] hub 5-0:1.0: USB hub found
[ 2.404957] hub 5-0:1.0: 2 ports detected
[ 2.405041] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.405047] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.405051] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.405088] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.405124] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
[ 2.405196] usb usb6: configuration #1 chosen from 1 choice
[ 2.405219] hub 6-0:1.0: USB hub found
[ 2.405225] hub 6-0:1.0: 2 ports detected
[ 2.405303] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.405309] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.405313] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.405352] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.405377] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 2.405444] usb usb7: configuration #1 chosen from 1 choice
[ 2.405467] hub 7-0:1.0: USB hub found
[ 2.405472] hub 7-0:1.0: 2 ports detected
[ 2.405596] usbcore: registered new interface driver libusual
[ 2.405624] usbcore: registered new interface driver usbserial
[ 2.405634] USB Serial support registered for generic
[ 2.405649] usbcore: registered new interface driver usbserial_generic
[ 2.405651] usbserial: USB Serial Driver core
[ 2.405698] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.409010] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.413546] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.413551] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.413554] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.413556] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.413558] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.416037] mice: PS/2 mouse device common for all mice
[ 2.428068] rtc_cmos 00:07: RTC can wake from S4
[ 2.428100] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 2.428132] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 2.428186] device-mapper: uevent: version 1.0.3
[ 2.428264] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 2.428328] device-mapper: multipath: version 1.0.5 loaded
[ 2.428331] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.428401] EISA: Probing bus 0 at eisa.0
[ 2.428408] Cannot allocate resource for EISA slot 1
[ 2.428410] Cannot allocate resource for EISA slot 2
[ 2.428412] Cannot allocate resource for EISA slot 3
[ 2.428415] Cannot allocate resource for EISA slot 4
[ 2.428417] Cannot allocate resource for EISA slot 5
[ 2.428419] Cannot allocate resource for EISA slot 6
[ 2.428421] Cannot allocate resource for EISA slot 7
[ 2.428427] EISA: Detected 0 cards.
[ 2.428533] cpuidle: using governor ladder
[ 2.428648] cpuidle: using governor menu
[ 2.429133] TCP cubic registered
[ 2.429226] NET: Registered protocol family 10
[ 2.429635] lo: Disabled Privacy Extensions
[ 2.429958] NET: Registered protocol family 17
[ 2.429973] Bluetooth: L2CAP ver 2.11
[ 2.429975] Bluetooth: L2CAP socket layer initialized
[ 2.429978] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.429980] Bluetooth: SCO socket layer initialized
[ 2.430008] Bluetooth: RFCOMM socket layer initialized
[ 2.430014] Bluetooth: RFCOMM TTY layer initialized
[ 2.430015] Bluetooth: RFCOMM ver 1.10
[ 2.430058] Marking TSC unstable due to TSC halts in idle
[ 2.430876] Using IPI No-Shortcut mode
[ 2.430940] registered taskstats version 1
[ 2.431058] Magic number: 9:959:578
[ 2.431080] platform pcspkr: hash matches
[ 2.431149] rtc_cmos 00:07: setting system clock to 2009-05-25 10:35:10 UTC (1243247710)
[ 2.431152] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.431154] EDD information not available.
[ 2.431423] Freeing unused kernel memory: 532k freed
[ 2.431574] Write protecting the kernel text: 4128k
[ 2.431634] Write protecting the kernel read-only data: 1532k
[ 2.618828] sky2 driver version 1.22
[ 2.618885] sky2 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.618903] sky2 0000:08:00.0: setting latency timer to 64
[ 2.618964] sky2 0000:08:00.0: Yukon-2 FE chip revision 1
[ 2.683242] sky2 0000:08:00.0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 2.683244] Part Number: Yukon 88E8036
[ 2.683246] Engineering Level: Rev. 1.6
[ 2.683248] Manufacturer: Marvell
[ 2.683455] sky2 0000:08:00.0: irq 2297 for MSI/MSI-X
[ 2.686113] sky2 eth0: addr 00:1a:80:20:28:8d
[ 2.686503] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.737205] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 2.767733] ohci1394 0000:09:03.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.817506] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[fc102000-fc1027ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 2.876300] usb 1-2: configuration #1 chosen from 1 choice
[ 3.048037] usb 2-3: new high speed USB device using ehci_hcd and address 3
[ 3.177990] usb 2-3: configuration #1 chosen from 1 choice
[ 3.178367] hub 2-3:1.0: USB hub found
[ 3.178726] hub 2-3:1.0: 4 ports detected
[ 3.353706] PM: Starting manual resume from disk
[ 3.353709] PM: Resume from partition 8:4
[ 3.353711] PM: Checking hibernation image.
[ 3.353952] PM: Resume from disk failed.
[ 3.390557] kjournald starting. Commit interval 5 seconds
[ 3.390570] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.424069] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 3.603991] usb 5-1: configuration #1 chosen from 1 choice
[ 4.140544] ieee1394: Host added: ID:BUS[0-00:1023] GUID[08004603027d1f4d]
[ 10.686320] udev: starting version 141
[ 10.999005] cfg80211: Calling CRDA to update world regulatory domain
[ 11.275574] cfg80211: World regulatory domain updated:
[ 11.275578] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.275580] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.275583] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.275585] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.275587] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.275589] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.382763] Linux agpgart interface v0.103
[ 11.442663] iTCO_vendor_support: vendor-support=0
[ 11.459117] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 11.459419] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 11.459504] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 11.526140] usbcore: registered new interface driver hiddev
[ 11.567571] input: Microsoft Microsoft� 2.4GHz Transceiver V2.0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input4
[ 11.569022] generic-usb 0003:045E:071F.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft� 2.4GHz Transceiver V2.0] on usb-0000:00:1d.0-1/input0
[ 11.569041] usbcore: registered new interface driver usbhid
[ 11.569064] usbhid: v2.6:USB HID core driver
[ 11.663701] sony-laptop: Sony Notebook Control Driver v0.6.
[ 11.666105] input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:29/SNY5001:00/input/input5
[ 11.669182] input: Sony Vaio Jogdial as /devices/virtual/input/input6
[ 11.671432] sony-laptop: detected Sony Vaio FZ Series
[ 11.803941] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 12.364148] nvidia: module license 'NVIDIA' taints kernel.
[ 12.384933] Linux video capture interface: v2.00
[ 12.446583] tifm_7xx1 0000:09:03.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 12.499626] yenta_cardbus 0000:09:03.0: CardBus bridge found [104d:9005]
[ 12.499649] yenta_cardbus 0000:09:03.0: Enabling burst memory read transactions
[ 12.499655] yenta_cardbus 0000:09:03.0: Using CSCINT to route CSC interrupts to PCI
[ 12.499657] yenta_cardbus 0000:09:03.0: Routing CardBus interrupts to PCI
[ 12.499663] yenta_cardbus 0000:09:03.0: TI: mfunc 0x01121b22, devctl 0x64
[ 12.519702] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 12.532540] uvcvideo: Found UVC 1.00 device <unnamed> (05ca:183b)
[ 12.532742] uvcvideo: Failed to query (135) UVC control 1 (unit 0) : -32 (exp. 26).
[ 12.533455] uvcvideo: Failed to query (129) UVC control 1 (unit 0) : -32 (exp. 26).
[ 12.533458] uvcvideo: Failed to initialize the device (-5).
[ 12.533491] usbcore: registered new interface driver uvcvideo
[ 12.533517] USB Video Class driver (v0.1.0)
[ 12.593931] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 12.593935] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 12.594035] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 12.594064] iwlagn 0000:06:00.0: setting latency timer to 64
[ 12.594130] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[ 12.617569] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.617586] nvidia 0000:01:00.0: setting latency timer to 64
[ 12.617777] NVRM: loading NVIDIA UNIX x86 Kernel Module 180.44 Mon Mar 23 14:59:10 PST 2009
[ 12.637473] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
[ 12.637548] iwlagn 0000:06:00.0: irq 2296 for MSI/MSI-X
[ 12.638697] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 12.757420] yenta_cardbus 0000:09:03.0: ISA IRQ mask 0x0cf8, PCI irq 16
[ 12.757424] yenta_cardbus 0000:09:03.0: Socket status: 30000006
[ 12.757428] pci_bus 0000:09: Raising subordinate bus# of parent bus (#09) from #0a to #0d
[ 12.757435] yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge I/O window: 0x7000 - 0x7fff
[ 12.757437] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x7000-0x7fff: clean.
[ 12.757667] yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge Memory window: 0xfc100000 - 0xfc1fffff
[ 12.757669] yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
[ 12.773410] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 12.773477] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.000073] Clocksource tsc unstable (delta = -103936248 ns)
[ 13.100988] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 13.103117] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 13.104000] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:<6>input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input8
[ 13.104733] clean.
[ 13.104771] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 13.105712] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 13.123615] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input9
[ 13.281372] lp: driver loaded but no devices found
[ 13.418460] Adding 2883656k swap on /dev/sda4. Priority:-1 extents:1 across:2883656k
[ 13.953045] EXT3 FS on sda3, internal journal
[ 15.052275] type=1505 audit(1243236923.120:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2171
[ 15.100729] type=1505 audit(1243236923.165:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2175
[ 15.100819] type=1505 audit(1243236923.165:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2175
[ 15.100854] type=1505 audit(1243236923.165:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2175
[ 15.100889] type=1505 audit(1243236923.165:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2175
[ 15.214215] type=1505 audit(1243236923.281:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2180
[ 15.214369] type=1505 audit(1243236923.281:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2180
[ 15.238862] type=1505 audit(1243236923.304:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2184
[ 18.088289] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 18.088291] Bluetooth: BNEP filters: protocol multicast
[ 18.107114] Bridge firewalling registered
[ 19.915422] ppdev: user-space parallel port driver
[ 23.940105] sky2 eth0: enabling interface
[ 23.940301] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.940898] iwlagn 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
[ 24.013407] iwlagn: Radio disabled by HW RF Kill switch
[ 24.230069] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.615032] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 25.615209] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 35.852062] eth0: no IPv6 routers present
[ 84.452086] usb 2-3: reset high speed USB device using ehci_hcd and address 3
[ 84.864378] usb 2-3.4: new full speed USB device using ehci_hcd and address 4
[ 84.962793] usb 2-3.4: configuration #1 chosen from 1 choice
[ 85.037177] usblp0: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x03F0 pid 0x3D11
[ 85.037215] usbcore: registered new interface driver usblp
[ 322.172360] CE: hpet increasing min_delta_ns to 15000 nsec
[ 355.797570] CE: hpet increasing min_delta_ns to 22500 nsec
[ 475.845268] CE: hpet increasing min_delta_ns to 33750 nsec
[ 615.845280] CE: hpet increasing min_delta_ns to 50624 nsec
[ 725.800828] CE: hpet increasing min_delta_ns to 75936 nsec
[ 2153.394122] usblp0: removed
[ 2755.858536] CE: hpet increasing min_delta_ns to 113904 nsec
[ 2955.902672] CE: hpet increasing min_delta_ns to 170856 nsec
[ 3755.872401] CE: hpet increasing min_delta_ns to 256284 nsec
[ 5795.841615] CE: hpet increasing min_delta_ns to 384426 nsec
[ 8102.486142] usb 2-3.4: USB disconnect, address 4
[ 8345.134292] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[ 8345.276114] usb 2-3: USB disconnect, address 3
[18310.607077] usbcore: deregistering interface driver uvcvideo
[18310.632914] uvcvideo: Found UVC 1.00 device <unnamed> (05ca:183b)
[18310.633874] input: UVC Camera (05ca:183b) as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input10
[18310.649341] usbcore: registered new interface driver uvcvideo
[18310.649351] USB Video Class driver (v0.1.0)


Τα αποτελέσματα της uname -a:

Κώδικας: Επιλογή όλων

Linux stephanos-laptop 2.6.28-11-generic #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 i686 GNU/Linux


[grammo]

Χμμμ... Τώρα που ξανάνοιξα το cheese δουλεύει κανονικά πάλι... Περίεργο ε;

[linuxman]

Χμμμ... Τώρα που ξανάνοιξα το cheese δουλεύει κανονικά πάλι... Περίεργο ε;

Ναι εγώ έχω

Κώδικας: Επιλογή όλων

uname -a
Linux linuxman-jaunty 2.6.28-12-generic

, εδώ είναι δεν έχεις όλες τις πηγές λογισμικού ενεργές , άνοιξε τις και επίσης και όλες τις ενημερώσεις τσέκαρε .

[grammo]

εδώ είναι δεν έχεις όλες τις πηγές λογισμικού ενεργές , άνοιξε τις και επίσης και όλες τις ενημερώσεις τσέκαρε .

Δεν κατάλαβα τι εννοείς! Επίσης παρατηρώ ότι κάθε φορά που κλείνει το pc, δε δουλεύει η κάμερα...
Μπορείς να μου πεις τι πρέπει να κάνω;

[linuxman]

εδώ είναι δεν έχεις όλες τις πηγές λογισμικού ενεργές , άνοιξε τις και επίσης και όλες τις ενημερώσεις τσέκαρε .

Δεν κατάλαβα τι εννοείς! Επίσης παρατηρώ ότι κάθε φορά που κλείνει το pc, δε δουλεύει η κάμερα...
Μπορείς να μου πεις τι πρέπει να κάνω;

Δες αυτό για πηγές λογισμικού viewtopic.php?f=9&t=398 κάνε τα ίδια βήματα και μετά θα δούμε .