DVD EZMaker USB Gold Πως θα δουλέψει

[spyroskaftanis]

δεν μπορώ να βγάλω την webcam γιατί είναι ενσωματωμένη στο laptop. Δεν νομίζω να υπάρχει τρόπος να την βγάλω

[logari81]

έσβησα τις διπλές σου δημοσιεύσεις

αφού δεν μπορεις να την αποσυνδεσεις δεν πειράζει, απλώς αυτό θα απλοποιούσε λίγο τα πράγματα. Καταφερες να βρεις την ρυθμιση για το video input στο tvtime;

[spyroskaftanis]

όχι. δοκόμασα τα πάντα αλλά δεν νομίζω να δουλεύει τελικά. Πείραξα όλες τις ρυθμίσεις, αλλά συνέχισε να μου λέει no signal

[logari81]

επειδη στο αποτελεσμα του lsusb που ειχες δώσει στην αρχή δεν φαινεται η συσκευη κανε λιγο το παρακάτω.

... DVD EZMaker USB Gold συνδεμενο (σε κανονική θυρα usb κι οχι σε hub), κανε επανεκκίνηση και δωσε μας ξανα τα αποτελεσματα των

Κώδικας: Επιλογή όλων

lsusb
dmesg

[spyroskaftanis]

lsusb-

Κώδικας: Επιλογή όλων

Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 003: ID 07ca:c038 AVerMedia Technologies, Inc.
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 04f2:b018 Chicony Electronics Co., Ltd Video Device
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 0a5c:2101 Broadcom Corp. A-Link BlueUsbA2 Bluetooth
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


dmesg-

Κώδικας: Επιλογή όλων

[ 0.584024] system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
[ 0.584027] system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
[ 0.584030] system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
[ 0.584033] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.584037] system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
[ 0.584040] system 00:01: iomem range 0xfed40000-0xfed44fff could not be reserved
[ 0.584043] system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
[ 0.584052] system 00:05: iomem range 0xfed00000-0xfed003ff could not be reserved
[ 0.584059] system 00:07: ioport range 0x680-0x69f has been reserved
[ 0.584062] system 00:07: ioport range 0x800-0x80f has been reserved
[ 0.584065] system 00:07: ioport range 0x1000-0x107f has been reserved
[ 0.584068] system 00:07: ioport range 0x1180-0x11bf has been reserved
[ 0.584071] system 00:07: ioport range 0x1640-0x164f has been reserved
[ 0.584074] system 00:07: ioport range 0xfe00-0xfe00 has been reserved
[ 0.584077] system 00:07: ioport range 0xff00-0xff7f has been reserved
[ 0.619176] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.619181] pci 0000:00:1c.0: IO window: 0x2000-0x2fff
[ 0.619187] pci 0000:00:1c.0: MEM window: 0xb0000000-0xb3ffffff
[ 0.619193] pci 0000:00:1c.0: PREFETCH window: 0x000000c8000000-0x000000cbffffff
[ 0.619202] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04
[ 0.619205] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 0.619212] pci 0000:00:1c.1: MEM window: 0xf4000000-0xf7ffffff
[ 0.619217] pci 0000:00:1c.1: PREFETCH window: 0x000000f0000000-0x000000f3ffffff
[ 0.619225] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:06
[ 0.619229] pci 0000:00:1c.2: IO window: 0x4000-0x4fff
[ 0.619235] pci 0000:00:1c.2: MEM window: 0xa8000000-0xabffffff
[ 0.619240] pci 0000:00:1c.2: PREFETCH window: 0x000000c0000000-0x000000c3ffffff
[ 0.619248] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:08
[ 0.619252] pci 0000:00:1c.3: IO window: 0x5000-0x5fff
[ 0.619259] pci 0000:00:1c.3: MEM window: 0xa0000000-0xa3ffffff
[ 0.619264] pci 0000:00:1c.3: PREFETCH window: 0x000000b8000000-0x000000bbffffff
[ 0.619272] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0a
[ 0.619274] pci 0000:00:1c.4: IO window: disabled
[ 0.619280] pci 0000:00:1c.4: MEM window: disabled
[ 0.619285] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.619294] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:0c
[ 0.619296] pci 0000:00:1c.5: IO window: disabled
[ 0.619302] pci 0000:00:1c.5: MEM window: 0xf8200000-0xf82fffff
[ 0.619307] pci 0000:00:1c.5: PREFETCH window: disabled
[ 0.619316] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0e
[ 0.619318] pci 0000:00:1e.0: IO window: disabled
[ 0.619324] pci 0000:00:1e.0: MEM window: 0xf8300000-0xf83fffff
[ 0.619329] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.619346] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.619352] pci 0000:00:1c.0: setting latency timer to 64
[ 0.619362] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.619367] pci 0000:00:1c.1: setting latency timer to 64
[ 0.619377] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.619382] pci 0000:00:1c.2: setting latency timer to 64
[ 0.619392] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.619398] pci 0000:00:1c.3: setting latency timer to 64
[ 0.619407] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.619412] pci 0000:00:1c.4: setting latency timer to 64
[ 0.619421] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.619427] pci 0000:00:1c.5: setting latency timer to 64
[ 0.619435] pci 0000:00:1e.0: setting latency timer to 64
[ 0.619439] bus: 00 index 0 io port: [0, ffff]
[ 0.619441] bus: 00 index 1 mmio: [0, ffffffff]
[ 0.619443] bus: 02 index 0 io port: [2000, 2fff]
[ 0.619446] bus: 02 index 1 mmio: [b0000000, b3ffffff]
[ 0.619448] bus: 02 index 2 mmio: [c8000000, cbffffff]
[ 0.619450] bus: 02 index 3 mmio: [0, 0]
[ 0.619452] bus: 04 index 0 io port: [3000, 3fff]
[ 0.619454] bus: 04 index 1 mmio: [f4000000, f7ffffff]
[ 0.619456] bus: 04 index 2 mmio: [f0000000, f3ffffff]
[ 0.619458] bus: 04 index 3 mmio: [0, 0]
[ 0.619460] bus: 06 index 0 io port: [4000, 4fff]
[ 0.619462] bus: 06 index 1 mmio: [a8000000, abffffff]
[ 0.619465] bus: 06 index 2 mmio: [c0000000, c3ffffff]
[ 0.619466] bus: 06 index 3 mmio: [0, 0]
[ 0.619468] bus: 08 index 0 io port: [5000, 5fff]
[ 0.619470] bus: 08 index 1 mmio: [a0000000, a3ffffff]
[ 0.619473] bus: 08 index 2 mmio: [b8000000, bbffffff]
[ 0.619475] bus: 08 index 3 mmio: [0, 0]
[ 0.619476] bus: 0a index 0 mmio: [0, 0]
[ 0.619478] bus: 0a index 1 mmio: [0, 0]
[ 0.619480] bus: 0a index 2 mmio: [0, 0]
[ 0.619482] bus: 0a index 3 mmio: [0, 0]
[ 0.619484] bus: 0c index 0 mmio: [0, 0]
[ 0.619485] bus: 0c index 1 mmio: [f8200000, f82fffff]
[ 0.619488] bus: 0c index 2 mmio: [0, 0]
[ 0.619489] bus: 0c index 3 mmio: [0, 0]
[ 0.619491] bus: 0e index 0 mmio: [0, 0]
[ 0.619493] bus: 0e index 1 mmio: [f8300000, f83fffff]
[ 0.619495] bus: 0e index 2 mmio: [0, 0]
[ 0.619497] bus: 0e index 3 io port: [0, ffff]
[ 0.619499] bus: 0e index 4 mmio: [0, ffffffff]
[ 0.619507] NET: Registered protocol family 2
[ 0.632049] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.632280] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.632653] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.632849] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.632853] TCP reno registered
[ 0.636073] NET: Registered protocol family 1
[ 0.636186] checking if image is initramfs...<6>ACPI: EC: GPE storm detected, transactions will use polling mode
[ 0.965041] it is
[ 1.322524] Freeing initrd memory: 8018k freed
[ 1.322713] Simple Boot Flag at 0x38 set to 0x1
[ 1.323627] audit: initializing netlink socket (disabled)
[ 1.323650] type=2000 audit(1247817433.320:1): initialized
[ 1.328703] highmem bounce pool size: 64 pages
[ 1.328710] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.330944] VFS: Disk quotas dquot_6.5.1
[ 1.331024] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.331121] msgmni has been set to 1743
[ 1.331238] io scheduler noop registered
[ 1.331240] io scheduler anticipatory registered
[ 1.331243] io scheduler deadline registered
[ 1.331254] io scheduler cfq registered (default)
[ 1.331269] pci 0000:00:02.0: Boot video device
[ 1.331568] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.331679] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.331787] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 1.331827] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 1.331863] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 1.332065] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 1.332177] pcieport-driver 0000:00:1c.1: found MSI capability
[ 1.332288] pci_express 0000:00:1c.1:pcie00: allocate port service
[ 1.332326] pci_express 0000:00:1c.1:pcie02: allocate port service
[ 1.332364] pci_express 0000:00:1c.1:pcie03: allocate port service
[ 1.332561] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 1.332672] pcieport-driver 0000:00:1c.2: found MSI capability
[ 1.332783] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 1.332819] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 1.332856] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 1.333068] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 1.333183] pcieport-driver 0000:00:1c.3: found MSI capability
[ 1.333294] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 1.333334] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 1.333370] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 1.333577] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 1.333692] pcieport-driver 0000:00:1c.4: found MSI capability
[ 1.333802] pci_express 0000:00:1c.4:pcie00: allocate port service
[ 1.333840] pci_express 0000:00:1c.4:pcie02: allocate port service
[ 1.333881] pci_express 0000:00:1c.4:pcie03: allocate port service
[ 1.334085] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 1.334195] pcieport-driver 0000:00:1c.5: found MSI capability
[ 1.334306] pci_express 0000:00:1c.5:pcie00: allocate port service
[ 1.334346] pci_express 0000:00:1c.5:pcie02: allocate port service
[ 1.334383] pci_express 0000:00:1c.5:pcie03: allocate port service
[ 1.334811] isapnp: Scanning for PnP cards...
[ 1.692208] isapnp: No Plug & Play device found
[ 1.722446] hpet_resources: 0xfed00000 is busy
[ 1.722510] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.724700] brd: module loaded
[ 1.724763] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.724876] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.766960] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.766966] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.767174] mice: PS/2 mouse device common for all mice
[ 1.770344] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.770382] rtc0: alarms up to one month, y3k, hpet irqs
[ 1.770502] EISA: Probing bus 0 at eisa.0
[ 1.770511] Cannot allocate resource for EISA slot 1
[ 1.770514] Cannot allocate resource for EISA slot 2
[ 1.770516] Cannot allocate resource for EISA slot 3
[ 1.770519] Cannot allocate resource for EISA slot 4
[ 1.770521] Cannot allocate resource for EISA slot 5
[ 1.770541] EISA: Detected 0 cards.
[ 1.770545] cpuidle: using governor ladder
[ 1.770547] cpuidle: using governor menu
[ 1.771048] TCP cubic registered
[ 1.771075] Using IPI No-Shortcut mode
[ 1.771236] registered taskstats version 1
[ 1.771360] Magic number: 1:466:976
[ 1.771369] tty ttyc3: hash matches
[ 1.771473] rtc_cmos 00:08: setting system clock to 2009-07-17 07:57:14 UTC (1247817434)
[ 1.771476] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.771478] EDD information not available.
[ 1.771717] Freeing unused kernel memory: 428k freed
[ 1.771754] Write protecting the kernel text: 2580k
[ 1.771780] Write protecting the kernel read-only data: 940k
[ 1.804279] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 1.932068] fuse init (API version 7.9)
[ 2.001504] ACPI: SSDT 7F6D9679, 027A (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 2.001941] ACPI: SSDT 7F6D914A, 04AA (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 2.004554] Monitor-Mwait will be used to enter C-1 state
[ 2.004557] Monitor-Mwait will be used to enter C-2 state
[ 2.004560] Monitor-Mwait will be used to enter C-3 state
[ 2.016121] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.016176] processor ACPI0007:00: registered as cooling_device0
[ 2.016180] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.016560] ACPI: SSDT 7F6D98F3, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
[ 2.016952] ACPI: SSDT 7F6D95F4, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
[ 2.020008] Marking TSC unstable due to TSC halts in idle
[ 2.024204] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.024249] processor ACPI0007:01: registered as cooling_device1
[ 2.024253] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.334790] usbcore: registered new interface driver usbfs
[ 2.334816] usbcore: registered new interface driver hub
[ 2.342349] usbcore: registered new device driver usb
[ 2.344535] USB Universal Host Controller Interface driver v3.0
[ 2.344581] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.344596] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.344602] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.344643] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.344694] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[ 2.344838] usb usb1: configuration #1 chosen from 1 choice
[ 2.344866] hub 1-0:1.0: USB hub found
[ 2.344873] hub 1-0:1.0: 2 ports detected
[ 2.348739] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 2.442629] No dock devices found.
[ 2.456161] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.456175] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.456181] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.456207] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 2.456255] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[ 2.456374] usb usb2: configuration #1 chosen from 1 choice
[ 2.456444] hub 2-0:1.0: USB hub found
[ 2.456452] hub 2-0:1.0: 2 ports detected
[ 2.456673] SCSI subsystem initialized
[ 2.519782] libata version 3.00 loaded.
[ 2.664387] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.664411] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.664417] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.664448] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 2.668365] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.668379] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.668397] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf8604800
[ 2.681045] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.681207] usb usb3: configuration #1 chosen from 1 choice
[ 2.681236] hub 3-0:1.0: USB hub found
[ 2.681244] hub 3-0:1.0: 4 ports detected
[ 2.888559] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.888574] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.888580] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.888606] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 2.888651] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[ 2.888740] usb usb4: configuration #1 chosen from 1 choice
[ 2.888765] hub 4-0:1.0: USB hub found
[ 2.888771] hub 4-0:1.0: 2 ports detected
[ 3.001246] Clocksource tsc unstable (delta = -187518513 ns)
[ 3.096460] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.096472] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.096478] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.096501] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 3.096550] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[ 3.096629] usb usb5: configuration #1 chosen from 1 choice
[ 3.096653] hub 5-0:1.0: USB hub found
[ 3.096659] hub 5-0:1.0: 2 ports detected
[ 3.201456] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.201465] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.201471] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.201494] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 3.201536] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[ 3.201619] usb usb6: configuration #1 chosen from 1 choice
[ 3.201645] hub 6-0:1.0: USB hub found
[ 3.201651] hub 6-0:1.0: 2 ports detected
[ 3.248252] usb 3-2: new high speed USB device using ehci_hcd and address 2
[ 3.305341] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.305360] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.305364] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.305386] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 3.309290] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.309300] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.309305] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8604c00
[ 3.424076] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.424203] usb usb7: configuration #1 chosen from 1 choice
[ 3.424246] hub 7-0:1.0: USB hub found
[ 3.424257] hub 7-0:1.0: 6 ports detected
[ 3.486885] usb 3-2: configuration #1 chosen from 1 choice
[ 3.634935] pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.634978] pata_acpi 0000:00:1f.1: setting latency timer to 64
[ 3.634999] pata_acpi 0000:00:1f.1: PCI INT A disabled
[ 3.635124] tg3.c:v3.94 (August 14, 2008)
[ 3.635182] tg3 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 3.635200] tg3 0000:04:00.0: setting latency timer to 64
[ 3.635459] ahci 0000:00:1f.2: version 3.0
[ 3.635473] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.635616] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 3.635619] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
[ 3.635629] ahci 0000:00:1f.2: setting latency timer to 64
[ 3.635857] scsi0 : ahci
[ 3.635966] scsi1 : ahci
[ 3.636043] scsi2 : ahci
[ 3.636153] ata1: SATA max UDMA/133 abar m2048@0xf8604000 port 0xf8604100 irq 217
[ 3.636159] ata2: SATA max UDMA/133 abar m2048@0xf8604000 port 0xf8604180 irq 217
[ 3.636165] ata3: SATA max UDMA/133 abar m2048@0xf8604000 port 0xf8604200 irq 217
[ 3.949573] eth0: Tigon3 [partno(BCM95906) rev c002 PHY(5906)] (PCI Express) 10/100Base-TX Ethernet 00:16:d4:d9:e4:ca
[ 3.949577] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
[ 3.949579] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 3.956255] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.956964] ata1.00: _GTF unexpected object type 0x1
[ 4.008637] ata1.00: ATA-8: WDC WD1600BEVS-00UST0, 01.01A01, max UDMA/133
[ 4.008642] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.009686] ata1.00: _GTF unexpected object type 0x1
[ 4.009886] ata1.00: configured for UDMA/133
[ 4.096253] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 4.261731] usb 2-1: configuration #1 chosen from 1 choice
[ 4.348284] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.428263] usb 7-6: new high speed USB device using ehci_hcd and address 3
[ 4.561252] usb 7-6: configuration #1 chosen from 1 choice
[ 4.684260] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.700431] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 01.0 PQ: 0 ANSI: 5
[ 4.700562] ohci1394 0000:0e:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 4.753306] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[f8300000-f83007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 4.761927] ata_piix 0000:00:1f.1: version 2.12
[ 4.761943] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 4.762000] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 4.762082] scsi3 : ata_piix
[ 4.762150] scsi4 : ata_piix
[ 4.762914] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[ 4.762917] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 4.765927] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.778697] Driver 'sd' needs updating - please use bus_type methods
[ 4.778802] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 4.778819] sd 0:0:0:0: [sda] Write Protect is off
[ 4.778822] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.778848] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.778912] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 4.778927] sd 0:0:0:0: [sda] Write Protect is off
[ 4.778929] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.778955] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.778958] sda:<6>usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 4.831343] sda1 sda2 < sda5 >
[ 4.859968] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.924727] ata4.00: ATAPI: Optiarc DVD RW AD-7530B, NX03, max UDMA/33
[ 4.940566] ata4.00: configured for UDMA/33
[ 4.982884] usb 4-1: configuration #1 chosen from 1 choice
[ 4.998707] usbcore: registered new interface driver hiddev
[ 5.014088] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1:1.0/input/input2
[ 5.014357] input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-1
[ 5.014374] usbcore: registered new interface driver usbhid
[ 5.014377] usbhid: v2.6:USB HID core driver
[ 5.110956] scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7530B NX03 PQ: 0 ANSI: 5
[ 5.111168] scsi 3:0:0:0: Attached scsi generic sg1 type 5
[ 5.132890] Driver 'sr' needs updating - please use bus_type methods
[ 5.143034] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.143040] Uniform CD-ROM driver Revision: 3.20
[ 5.143177] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 5.390899] PM: Starting manual resume from disk
[ 5.390902] PM: Resume from partition 8:5
[ 5.390904] PM: Checking hibernation image.
[ 5.391132] PM: Resume from disk failed.
[ 5.465061] kjournald starting. Commit interval 5 seconds
[ 5.465076] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.028653] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f75bc40024e]
[ 13.109115] udevd version 124 started
[ 13.479371] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 13.503595] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.611609] Linux agpgart interface v0.103
[ 13.648765] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 13.676045] ACPI: Power Button (FF) [PWRF]
[ 13.676116] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[ 13.676189] ACPI: Lid Switch [LID0]
[ 13.676236] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[ 13.708028] ACPI: Power Button (CM) [PWRB]
[ 13.708261] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[ 13.708739] agpgart-intel 0000:00:00.0: detected 7676K stolen memory
[ 13.711261] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 13.790188] acpi device:0a: registered as cooling_device2
[ 13.790567] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:07/input/input6
[ 13.812027] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 13.820806] ACPI: WMI: Mapper loaded
[ 13.863844] ACPI: AC Adapter [ACAD] (on-line)
[ 13.920661] ACPI: Battery Slot [BAT1] (battery present)
[ 14.150477] Bluetooth: Core ver 2.13
[ 14.150925] NET: Registered protocol family 31
[ 14.150928] Bluetooth: HCI device and connection manager initialized
[ 14.150932] Bluetooth: HCI socket layer initialized
[ 14.316142] Linux video capture interface: v2.00
[ 14.392105] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 14.392212] usbcore: registered new interface driver btusb
[ 14.466651] iTCO_vendor_support: vendor-support=0
[ 14.613407] sdhci: Secure Digital Host Controller Interface driver
[ 14.613410] sdhci: Copyright(c) Pierre Ossman
[ 14.680605] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (04f2:b018)
[ 14.681135] sdhci-pci 0000:0e:06.1: SDHCI controller found [1180:0822] (rev 22)
[ 14.681157] sdhci-pci 0000:0e:06.1: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[ 14.682175] sdhci-pci 0000:0e:06.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 14.683346] input: USB 2.0 Camera as /devices/pci0000:00/0000:00:1a.7/usb3/3-2/3-2:1.0/input/input7
[ 14.683398] usbcore: registered new interface driver uvcvideo
[ 14.683402] USB Video Class driver (v0.1.0)
[ 14.684688] mmc0: SDHCI controller on PCI [0000:0e:06.1] using DMA
[ 14.730518] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 14.730618] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 14.730722] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 14.839846] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 15.027330] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 15.027382] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 15.062079] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 15.209967] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 15.209971] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 15.210082] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 15.210122] iwlagn 0000:0c:00.0: setting latency timer to 64
[ 15.210194] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[ 15.257536] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
[ 15.258875] iwlagn 0000:0c:00.0: PCI INT A disabled
[ 15.259264] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 17.165497] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input9
[ 18.110051] lp: driver loaded but no devices found
[ 18.284375] Adding 6040400k swap on /dev/sda5. Priority:-1 extents:1 across:6040400k
[ 18.829318] EXT3 FS on sda1, internal journal
[ 19.824022] type=1505 audit(1247817452.905:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4364
[ 19.974921] type=1505 audit(1247817453.057:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4369
[ 19.975148] type=1505 audit(1247817453.057:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4369
[ 20.016486] type=1505 audit(1247817453.101:5): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=4373
[ 20.259486] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.901672] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 24.306803] apm: BIOS not found.
[ 24.582359] ppdev: user-space parallel port driver
[ 26.329259] NET: Registered protocol family 10
[ 26.332833] lo: Disabled Privacy Extensions
[ 30.186728] Bluetooth: L2CAP ver 2.11
[ 30.186738] Bluetooth: L2CAP socket layer initialized
[ 30.291628] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 30.291642] Bluetooth: BNEP filters: protocol multicast
[ 30.313352] Bluetooth: RFCOMM socket layer initialized
[ 30.313895] Bluetooth: RFCOMM TTY layer initialized
[ 30.313905] Bluetooth: RFCOMM ver 1.10
[ 30.367903] Bridge firewalling registered
[ 30.421569] Bluetooth: SCO (Voice Link) ver 0.6
[ 30.421574] Bluetooth: SCO socket layer initialized
[ 34.641520] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 34.646127] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 34.646299] iwlagn 0000:0c:00.0: restoring config space at offset 0x1 (was 0x40100102, writing 0x40100106)
[ 34.648298] firmware: requesting iwlwifi-4965-2.ucode
[ 34.766895] [drm] Initialized drm 1.1.0 20060810
[ 34.789771] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 34.789789] pci 0000:00:02.0: setting latency timer to 64
[ 34.791100] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 34.971621] Registered led device: iwl-phy0:radio
[ 34.971804] Registered led device: iwl-phy0:assoc
[ 34.971916] Registered led device: iwl-phy0:RX
[ 34.972038] Registered led device: iwl-phy0:TX
[ 35.000155] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 35.135177] NET: Registered protocol family 17
[ 70.916070] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 91.470132] CPU0 attaching NULL sched-domain.
[ 91.470153] CPU1 attaching NULL sched-domain.
[ 91.476778] CPU0 attaching sched-domain:
[ 91.476789] domain 0: span 0-1 level MC
[ 91.476796] groups: 0 1
[ 91.476810] CPU1 attaching sched-domain:
[ 91.476815] domain 0: span 0-1 level MC
[ 91.476820] groups: 1 0
[ 94.563338] wlan0: authenticate with AP 00:13:33:17:ea:82
[ 94.565259] wlan0: authenticated
[ 94.565275] wlan0: associate with AP 00:13:33:17:ea:82
[ 94.567485] wlan0: RX AssocResp from 00:13:33:17:ea:82 (capab=0x411 status=0 aid=2)
[ 94.567498] wlan0: associated
[ 94.574800] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 105.389033] wlan0: no IPv6 routers present